Ultrasonic Testing in Everett
High-frequency sound-wave inspection for wall thickness, weld integrity and internal flaw detection.
Composite inspection crews at Boeing Everett need real-time visibility on UT phased-array calibration status — a single uncalibrated instrument fails composite PA scans across an entire shift.
How Ultrasonic Testing works
Piezoelectric transducers transmit and receive 0.5–25 MHz longitudinal or shear waves through the test article. Discontinuities reflect or diffract the wavefront; time-of-flight and amplitude analysis reveal flaw depth, size and through-wall position.
UT in Everett
Ultrasonic Testing in Everett is most often pulled into scope when aerospace (boeing 787, 777, 747) or composites inspection operators need FAA Part 145-grade evidence that an asset is fit for continued service. The recurring sites — Boeing Everett Factory and Naval Station Everett — write UT into pre-job inspection plans because high-frequency sound-wave inspection for wall thickness, weld integrity and internal flaw detection. Local contractors mobilise calibrated equipment, current ASNT Level II / III credentials, and procedure packages tied to ASME Section V and ASTM E164.
Quick facts
- Method: UT — Ultrasonic Testing
- Service area: Everett, WA
- Primary industries: Aerospace (Boeing 787, 777, 747), Composites inspection
- Key standards: ASME Section V, ASTM E164
Where UT shows up on Everett jobs
Industry relevance
Aerospace (Boeing 787, 777, 747) and Composites inspection operators in Everett pull UT into routine and turnaround scopes. The named recurring sites include Boeing Everett Factory and Naval Station Everett.
Acceptance criteria are written against FAA Part 145 and ratified at Level III sign-off for procedure qualification.
Compliance and safety
Ultrasonic Testing inspections in Everett reference ASME Section V, ASTM E164, ASTM E2375. Site-specific qualification matrices add operator-specific requirements on top.
Working with NDT Connect-listed providers ensures Level II/III currency, instrument-level calibration traceability, and digital record packages that survive audit retention demands.
Named Everett facilities served
Ultrasonic Testing scopes in Everett recur at the following operators and sites. Local contractors are pre-qualified at most of these gates.
Boeing Everett Factory
Aerospace — UT scope routine
Naval Station Everett
USN homeport (DDG / CG) — UT scope routine
Applicable standards and codes
Ultrasonic Testing inspections in Everett are written and accepted against:
ASME Section V
ASTM E164
ASTM E2375
ISO 16810
AWS D1.1
API 510 / 570 / 653
Local code authorities
Why UT is chosen
Single-sided access — no need to enter or open the asset
Quantitative thickness and flaw-depth data, not just go/no-go
Immediate result — no film processing latency
No ionising radiation; minimal exclusion zone
Typical applications
- •Wall-thickness surveys on in-service pressure piping (API 570)
- •Pre- and in-service weld inspection on pressure vessels (ASME Section VIII)
- •Corrosion mapping on storage tank shells and floors (API 653)
- •Forging and casting volumetric inspection
- •Bond-line inspection on composite laminates
The NDT footprint in Everett, WA reflects aerospace's share of the local economy and the supporting naval (ns everett) cluster. Boeing 777X composite wing — largest single composite UT/PAUT scan area in commercial aerospace. Ultrasonic Testing (UT) sits inside the recurring scope mix that Boeing Everett (777, 767, KC-46, 777X), Boeing Everett Factory, and the broader pacific northwest operator base put on contract every cycle.
a mid-band metro of about 826K residents keeps the certified-contractor base deep enough to absorb engine disc inspection surges without losing schedule. Programmes typically rotate around airframe lap joint populations, and UT is the examination most often written into the procedure pack at the gate.
Naval Station Everett — Pacific Fleet surface combatants need NAVSEA UT/MT/PT to T9074-AS-GIB-010/271. Cost-of-living index 142.5 and the medium transport surcharge band combine into the multiplier procurement teams budget against.
Code compliance on UT work in Everett, WA starts with the local authority stack — WA L&I 296-104, FAA Part 145, AS9100, NAVSEA T9074, Boeing PS-21202 (NDT). BPVC Sec V Art. 4 (UT general) is the method-level technical standard procedures qualify against, with AMS 2644, BPVC Sec V Art. 5 (UT thickness) and BPVC Sec VIII Div 1 UW-53 pulled in when scope crosses into aerospace territory. Boeing Everett (777, 767, KC-46, 777X) typically requires currency on both layers before a contractor crosses the gate.
- WA L&I 296-104
- FAA Part 145
- AS9100
- BPVC Sec V Art. 4 (UT general)
- BPVC Sec V Art. 5 (UT thickness)
- BPVC Sec VIII Div 1 UW-53
Ultrasonic Testing (UT) day-rates in Everett, WA cluster between $650–$975 for Level II crews, with a typical mid-point near $813. The medium transport-surcharge band and a cost-of-living index of 142.5 push rates above the national baseline (multiplier ×1.25). Local Level II inspector wages — $95,000 median per BLS — anchor that band. Outage windows add 25–40%; volume programmes negotiate 8–15% off.
| Line item | Rate | Detail |
|---|---|---|
| Hourly labour (Level II) | $81–$122/hr | standard programme rate |
| Hourly labour (Level III) | $176/hr | procedure qualification + disposition |
| Day rate (Level II) | $813/day | 8 hours, ≤30 km from base |
| Equipment surcharge | $350/day | instrument + consumables |
| Mobilisation | $525/trip | medium transport-surcharge band |
| Outage / night-shift uplift | +25–40% | turnaround windows and weekend work |
Effective multiplier vs national base: ×1.25 · transport surcharge band: medium.
Certified UT providers in Everett, WA typically serve a client base anchored by Boeing Everett (777, 767, KC-46, 777X), Naval Station Everett, and other pacific northwest operators. Posting a scope through NDT Connect routes the request to providers already pre-qualified at these gates — three to five parallel quotes typically return within 24–72 hours.
Major regional clients served
- Boeing Everett (777, 767, KC-46, 777X)
- Naval Station Everett
- Spirit AeroSystems Everett
- Crane Aerospace & Electronics
- Aviation Technical Services (ATS)
UT's role in Everett, WA's inspection economy is anchored to aerospace: Boeing Everett — 777, 767, KC-46, 777X production. The technique earns its keep on lamination detection in plate and pipe, and local pre-job plans often centre on landing-gear forging populations where composite delamination after impact have to be screened out before return-to-service.
On the ground, that translates to engine disc fluorescent PT line as the dominant scope, with engine disc inspection surges layered on every cycle. Boeing Everett (777, 767, KC-46, 777X) typically locks in standing-order coverage; smaller operators time spot-buys against contractor availability. The local pace — measured in 35 sq ft per shift — is what sets contractor utilisation and, downstream, the rate band procurement should expect.
Boeing 777X composite wing — largest single composite UT/PAUT scan area in commercial aerospace. Naval Station Everett — Pacific Fleet surface combatants need NAVSEA UT/MT/PT to T9074-AS-GIB-010/271. On the limitation side, difficult on coarse-grain austenitic stainless and inconel welds — local crews mitigate by procedure-level controls and RT (for volumetric crosscheck) where the indication class warrants it.
The Everett, WA certification economy is built around Puget Sound ASNT Section, AWS Puget Sound Section, and regional API exam access. Inspectors targeting UT work clear roughly 880 training hours to Level II, then layer AWS CWI and API tickets to qualify into the aerospace programmes that anchor local demand. Vendor-led training paths feed most of the local pipeline; apprenticeship routes carry the rest.
- ASNT chapter: Puget Sound ASNT Section
- AWS section: AWS Puget Sound Section
- API exam centre: access via nearest regional centre
How much does UT cost in Everett, WA?
UT (Ultrasonic Testing) day-rates in Everett, WA typically clear at $813/day for Level II crews, with the pricing multiplier on the national base running ×1.25 (transport surcharge band: medium). Local Level II inspector wages average $95,000/year per BLS, which anchors that day-rate band. Always solicit at least three parallel quotes before committing programme spend.
Which Everett, WA sites use UT most often?
Boeing Everett (777, 767, KC-46, 777X) and Naval Station Everett are the high-volume UT buyers in Everett, WA. The aerospace footprint at Boeing Everett Factory is a recurring UT mobilisation point. Pre-qualification at these gates is what unlocks the volume contracts.
What credentials do UT inspectors need to work in Everett, WA?
Working UT scope in Everett, WA requires ASNT Level II for the method (roughly 880 total training hours to qualify), plus Puget Sound ASNT Section membership is common. AWS CWI is required for welding-related scope; API 510/570/653 tickets unlock pressure-equipment work. API exam logistics route through the nearest regional centre.
What aerospace failure modes does UT screen for in Everett, WA?
On aerospace jobs in Everett, WA, UT is most often called for fatigue crack at fastener hole screening. Recurring scope on engine disc inspection cycles drives the volume. The technique sits inside WA L&I 296-104's acceptance framework, and local crews build inspection plans around the failure modes the aerospace owners audit hardest.
How fast can a UT crew mobilise in Everett, WA?
Routine UT scope in Everett, WA typically picks up a certified crew within 24–72 hours of posting a request — the deep contractor base around Boeing Everett (777, 767, KC-46, 777X) keeps mobilisation lead times short. Outage windows and turnaround support are negotiated against rotation; post the scope to NDT Connect to receive parallel quotes from providers already pre-qualified at Everett, WA sites.
What standards govern UT acceptance in Everett, WA?
UT examinations in Everett, WA reference BPVC Sec V Art. 4 (UT general) / BPVC Sec V Art. 5 (UT thickness) as the technical floor and WA L&I 296-104, FAA Part 145 for documentary compliance. Boeing Everett (777, 767, KC-46, 777X)'s qualification matrix layers an additional customer-specific spec on top — procedures must close on all three before the crew is cleared at the gate.
Ready for UT inspection in Everett?
Connect with certified UT providers in Everett. Parallel quotes, traceable calibration, audit-grade records.
Get a free quote todayOther NDT methods in Everett
Radiographic Testing
RT
Ionising-radiation imaging (X-ray or gamma) of internal weld structure on film or digital detector.
Magnetic Particle Testing
MT
Surface and near-surface crack detection on ferromagnetic materials via magnetic flux leakage.
Liquid Penetrant Testing
PT
Capillary-action surface flaw detection on any non-porous material using dye or fluorescent penetrant.
Visual Testing
VT
Code-required direct or remote visual examination of as-fabricated and in-service surfaces.
Ultrasonic Testing in nearby cities
Verified Everett, WA Inspection-Market Data
Hard numbers from BLS, EIA, AAPA, Census & API directories — anchoring this page to Everett, WA's actual NDT market, not a generic template.
- Local Wage Anchor — Level II NDT Technician
- $95K/yr typical for Everett, WA
- Metro Industrial Base
- 826K people in Snohomish County (within Seattle MSA)
- Sector Mix (NDT Demand Drivers)
- Aerospace (55%) · Naval (NS Everett) (18%) · Composites (15%)
- Port / Marine Workload
- Port of Everett (Specialty Boeing oversize cargo)
- Active API-Certified Inspectors (regional)
- ~40 API 510 · ~60 API 570 · ~30 API 653
- ASNT Chapter / Community
- Puget Sound ASNT Section
- Cost-of-Living Impact on Rate Cards
- COL index 142.5 (42.5 pts above national avg) · transport surcharge band: medium
Source: BLS OES May 2024 (Snohomish County subset of Seattle-Tacoma-Bellevue MSA)
Source: US Census ACS 2023
Source: BEA Regional Accounts 2023
Source: AAPA US Port Rankings 2023
Source: API ICP roster + state directories (est.)
Source: ASNT chapter directory
Source: C2ER ACCRA COL Index 2024
Continue Reading — In-Depth Guides
Authored by ASNT Level III inspectors. Real procedures, real numbers, real codes.
- Ultrasonic Testing — Complete GuidePhysics, calibration, codes, equipment, applications.
- Phased Array UT (PAUT) — Complete GuideBeam steering, focal laws, scan plans, ISO 13588.
- Ultrasonic Testing MethodMethod-level overview, equipment, standards.
- How to Calibrate a UT Flaw DetectorStep-by-step DAC, sensitivity, gate setup.
- How to Perform Thickness Survey on PipingUT scan plan, CMLs, API 570 grid.
Join NDT Connect — free
Need Ultrasonic Testing in Everett, or an inspector who offers it? Join NDT Connect free.
Free to join · No credit card · Provider profiles verified against ASNT & API rosters · Browse providers
