ASTM E164: Standard Practice for Ultrasonic Contact Testing of Weldments
Standard practice for ultrasonic testing of welds using contact method with straight and angle-beam transducers. ASTM E164 covers equipment requirements, procedures, and acceptance criteria for weld inspection. It is widely referenced in construction and fabrication specifications.
ASTM International is a consensus body that publishes test methods and practices used inside other codes; ASTM E-series documents are the most widely cited NDT references in North America.
ASTM standards become enforceable when invoked by a contract, by another code such as ASME Section V, or by a regulator citing them as the controlling test method.
ASTM E164 is invoked when the scope of work matches its title — standard practice for ultrasonic contact testing of weldments — and when the contract or regulatory regime cites it as the controlling document. Aerospace work treats the standard as a floor rather than a ceiling — most prime contractors layer their own internal procedures on top, with tighter acceptance criteria than the published code. In fabrication shops the standard is reproduced inside the written procedure book and referenced from every inspection report so that the auditor's paper trail leads back to the same paragraph the inspector worked from.
Methods covered
Industries
- Construction
- Manufacturing
- Aerospace
- Personnel qualification: examinations under ASTM E164 must be performed by inspectors qualified and certified to a recognised scheme (typically ASNT SNT-TC-1A, CP-189, or ISO 9712 depending on jurisdiction), with documented training hours, vision tests, and a controlling written practice.
- Written procedure: every examination requires a written, controlled procedure that names the method, equipment, calibration steps, scanning pattern, and acceptance criteria — and is qualified before first use.
- Equipment verification: ultrasonic instruments must be verified against a calibration block (V1, V2, IIW, or job-specific reference) at intervals defined by the procedure — typically before use, every four hours of scanning, on operator change, and at end of shift.
- Acceptance criteria: indications are evaluated against the standard's tabulated limits (length, depth, alignment, frequency); any indication exceeding the criteria is recorded, dispositioned, and either repaired or evaluated for fitness-for-service.
- Documentation: examination reports must include enough information for a third party to reproduce the inspection — equipment serial numbers, calibration records, inspector ID, sketches of indications, and the controlling procedure revision.
ASTM standards are reviewed on a five-year cycle and either reaffirmed, revised, or withdrawn. Revisions to ASTM E164 are generally evolutionary rather than revolutionary — clarifying language, adding new technique variants, or aligning with parallel ISO documents. The standard's designation includes the year of last revision (e.g. E709-21), and contracts that name a specific year freeze the inspection requirements to that revision.
An aerospace manufacturing line will reference ASTM E164 on the inspection-traveler card for each component; the inspection is performed by NAS 410-qualified personnel, and any indication exceeding the standard's limits triggers a Material Review Board disposition before the part is released to assembly.
What does ASTM E164 cover?
ASTM E164 (Standard Practice for Ultrasonic Contact Testing of Weldments) is published by ASTM International. Standard practice for ultrasonic testing of welds using contact method with straight and angle-beam transducers.
Is ASTM E164 mandatory or voluntary?
ASTM E164 is a consensus standard. It becomes mandatory when invoked by a contract, by another code that cites it (for example ASME Section V calling out an ASTM practice), or by a regulator that has adopted it into law in a specific jurisdiction.
Who is qualified to perform inspections under ASTM E164?
Inspections under ASTM E164 must be performed by personnel qualified and certified to a recognised NDT certification scheme — most commonly ASNT SNT-TC-1A or CP-189 in the United States, ISO 9712 in much of the rest of the world, and NAS 410 for aerospace work. The written practice that controls qualification must be in place before any examination is started.
Which other standards are commonly cited alongside ASTM E164?
ASTM E164 is most often cited together with the parent code that brings it into the contract — typically ASME Section V or VIII for U.S. pressure equipment, AWS D1.1 for structural welding, API 510/570/653 for in-service petroleum equipment, or the matching EN/ISO standard for European and international work.
Standard Code
ASTM E164
Organization
ASTM International
Methods Covered
1 method(s)
Industries
3 sector(s)
Need clarification on NDT terminology used in ASTM E164?
Browse NDT Glossary